Vernier Calipers (With Fine Adjustment)

Features:

• Provided with a fine - adjustment carriage to feed the slider finely.
• Provided with a fine - adjustment carriage to feed the slider finely.Permitting four types of different measurement (internal, external, depth and step).

Inside Calipers

Features:

• Specially designed for inside measurements in hard to reach places.
• With SPC data output.
• Digital readout to 0.01mm on the large and clear LCD screen for error-free reading.

Vernier Calipers With Long Jaws

Features:

• Long jaws for measuring hard-to-reach portions.
• Provided with a fine-adjustment carriage to feed the slider finely. (except for 543-109 and 543-110)

Offset Centerline Calipers

Features:

• Offset Centerline Calipers specially designed for center to center distance measurements on the same and offset planes.
• Hole diameter should be larger than 1.5mm (.06") but smaller than 10mm (.4").
• Can also measure from edge to center.
• Without Depth Bar.

Dial Calipers

Features:

• Permitting four types of different measurement (internal, external, depth and step).
• Slider displacements are amplified by a rack - and - pinion mechanism and indicated on the dial.
• Carbide Jaw Dial Calipers are also available.
• With clamping screw atop the slider.

ABS Digimatic Calipers

Mitutoyo's new ABS Digimatic Caliper "MYCAL Absolute" keeps track of its origin point once set. No more repeated zero setting is necessary with the "MYCAL Absolute" as well as no more care for the over - speed error. Whenever turned on, the large LCD screen displays the actual slider position ready to start measurement.

Features:

• ABS Digimatic Calipers display zero setting at any slider position along the scale for incremental comparison measurements. This switch will also allow return to the absolute mode and display of the true position from the origin point.
• It have large and clear LCD screen.
• Optional add-on DATA /HOLD Unit is available.
• Single SR44 battery operation with approx. 3.5 years battery life under normal working conditions.

Point Calipers

Features:

• The narrow tip jaws fit into very small grooves and tracks, making many previously difficult outside measurements far easier to obtain.
• Digital readout to 0.01mm on the large and clear LCD screen for error-free reading. Functions and optional accessories are the same as the standard ABS Digimatic Caliper.
• With Depth Bar.
• With SPC data output.

Neck Type ABS Digimatic Calipers

Features:

• Neck Type Calipers can measure wall thickness inside bores and recesses.
• Digital readout to 0.01mm on the large and clear LCD screen for error-free reading.
• With SPC data output.

Tube Thickness Type ABS Digimatic Calipers

Features:

• The main scale jaws is a round bar that facilitates measurements of tube wall thickness.
• Digital readout to 0.01mm on the large and clear LCD screen for error-free reading.
• With SPC data output.

Low Force Calipers

Features:

• Due to the low measuring force these calipers are ideal for elastic or resilient work pieces such as plastic parts and rubber parts that standard calipers can not measures.

Diamond Master Vernier Calipers

Features:

• The main and vernier scales are flush-fitted to eliminate parallax errors because of the diamond-shaped (octagonal) cross section of the main scale.
• With clamping screw below the slider.
• Permitting four types of different measurement (internal, external, depth and step).

Vernier Depth Gauges

Features:

• Base and measuring faces are hardened and micro-lapped.
• Made of hardened stainless steel.
• Wider extension bases are available.
• With or without a fine-adjustment carriage.

Mitutoyo Micrometers.

Dial Snap Meters Series 523.

Features:

• Direct GO/NO-GO judgment for mass-produced parts
• Spindle diameter: 8 mm (.315").
• Carbide-tipped measuring faces.
• Measuring force: 6 - 15N (600 - 1500gf).
• IP protection level: 54.

Disk Micrometers series 323, 223, 123.

Features:

• 0.7 mm edge thickness to enter narrow recesses.
• The disk micrometer is design to easily measure root tangent length of spur gears and herical gears.
• Diameters of measuring disk: 20 mm (.79").
• Provided with a standard except for 25 mm (1") model.
• The 323 series  (LCD readout type) is provided with SPC output.
• The 223 series is providing with a mechanical digit counter for quick reading of measurements.
• With Ratchet stop for constant force.

Blade Micrometers series 422, 122.

Features:

• The anvil and the spindle have a blade for measuring the groove diameters of shafts, keyways, and other hard-to-reach portions.
• With Ratchet stop for constant force.
• The 222 series is provided with a digit counter.
• Providing with a standard except for 25 mm (1") model.

Can Seam Micrometers series 347, 147.

Features:

• Measures the width, height, and depth of can seams.
• Three types of micrometers are available for: steel can, aluminum can, and sprayer cans.